View MB15C02PFV2_64527.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

FUJITSU SEMICONDUCTOR DATA SHEET
DS04-21348-3E
ASSP
Single Serial Input PLL Frequency Synthesizer
On-Chip prescaler
MB15C02
s DESCRIPTION
The Fujitsu MB15C02 is a serial input Phase Locked Loop (PLL) frequency synthesizer with a prescaler. A 64/65 division is available for the prescaler that enables pulse swallow operation. This operates with a supply voltage of 1.0 V (min.). MB15C02 is suitable for mobile communications, such as paging systems.
s FEATURES
* High frequency operation: 220 MHz max @VDD = 1.0 V to 1.5 V 330 MHz max @VDD = 1.2 V to 1.5 V 450 MHz max @VDD = 1.3 V to 1.5 V * Single power supply : VDD = 1.0 to 1.5 V * Power saving function * Pulse swallow function: 64/65 * Serial input 14-bit programmable reference divider: R = 5 to 16,383 * Serial input 18-bit programmable divider consisting of: - Binary 6-bit swallow counter: 0 to 63 - Binary 12-bit programmable counter: 5 to 4,095 * Wide operating temperature: Ta = -20 to 60C
s PACKAGES
16-pin, Plastic SSOP 20-pin, Plastic SSOP
(FPT-16P-M05)
(FPT-20P-M03)
1
MB15C02
s PIN ASSIGNMENTS
SSOP-20 pin
VDD Clock NC Data LE fin PS NC LD Do 1 2 3 4 5 6 7 8 9 10 20 19 18 17 Top View 16 15 14 13 12 11 VSS OSCIN NC OSCOUT TEST FC P NC R Vp
(FPT-20P-M03)
SSOP-16 pin
VSS OSCIN OSCOUT TEST FC P R Vp
VDD Clock Data LE fin PS LD Do
1 2 3 4 5 6 7 8 Top View
16 15 14 13 12 11 10 9
(FPT-16P-M05)
2
MB15C02
s PIN DESCRIPTIONS
Pin no. SSOP SSOP 16 20 1 2 - 3 4 1 2 3 4 5 Pin name VDD Clock NC Data LE I/O - I - I I Power supply voltage Clock input for the shift register.(Schmitt trigger input) Data is shifted into the shift register on the rising edge of the clock. No connection Serial data input using binary code.(Schmitt trigger input) Load enable signal input (Schmitt trigger input) When LE is high, the data in the shift register is transferred to a latch, according to the control bit in the serial data. Prescaler input. A bias circuit and amplifier are at input port. Connection with an external VCO should be done by AC coupling. Power saving mode control. This pin must be set at "L" at Power-ON. PS = "H" ; Normal mode PS = "L" ; Power saving mode No connection Lock detector signal output. When a PLL is locking, LD outputs "H". When a PLL is not locking, LD outputs "L". Charge pump output. Phase of the charge pump can be reversed by FC input. The Do output may be inverted by FC input. The relationships between the programmable reference divider output (fr) and the programmable divider output (fp) are shown below; fr > fp :"H" level (FC = "L"), "L" level (FC = "H") fr = fp : High impedance fr < fp :"L" level (FC = "L"), "H" level (FC = "H") Power supply for the charge pump. Phase comparator output pin (for external charge pump). Relation between the programmable reference divider output (fr) and the programmable divider output (fp) are shown below; When FC = "L" fr > fp : R = "L" level, P = "L" level fr = fp : R = "L" level, P = High impedance fr < fp : R = "H" level, P = High impedance When FC = "H" fr > fp : R = "H" level, P = High impedance fr = fp : R = "L" level, P = High impedance fr < fp : R = "L" level, P = "L" level No connection Phase comparator output pin (for external charge pump). Refer to Pin description for R. P pin is a Nch open drain output. Phase comparator input select pin. Test mode select pin. (Pull down resistor) Please set this pin to ground or open usually. Descriptions
5
6
fin
I
6 - 7
7 8 9
PS NC LD
I - O
8
10
Do
O
9
11
Vp
-
10
12
R
O
- 11 12 13
13 14 15 16
NC P FC TEST
- O I I
(Continued)
3
MB15C02
(Continued)
Pin no. SSOP SSOP 16 20 14 - 15 16 17 18 19 20 Pin name OSCOUT NC OSCIN VSS I/O O - I - Descriptions Oscillator output. Connection for an external crystal. No connection Programmable reference divider input. Oscillator input. Clock can be input to OSCIN from outside. In the case, please leave OSCOUT pin open and make connection with OSCIN as AC coupling. Ground pin.
4
MB15C02
s BLOCK DIAGRAM
VDD Programmable reference divider
Binary 14-bit reference counter
Crystal oscillator circuit
VSS
OSCIN
Intermittent mode control circuit 14-bit latch
14 OSCOUT
Clock
fr Phase comparator TEST
14
fp
FC Output control circuit
18-bit shift register Data Control register 18 LE
P
18-bit latch
Output control circuit
R
6
12
fin PS Prescaler Binary 6-bit swallow counter Binary 12-bit programmable counter Charge pump
VP
LD Lock detector Control circuit
Do
5
MB15C02
s ABSOLUTE MAXIMUM RATINGS
Parameter Power supply voltage Input voltage Output voltage Output current Storage temperature Symbol VDD, VP VIN VOUT IOUT Tstg Rating Min. GND-0.5 GND-0.5 GND-0.5 -10 -40 Max. +2.0 VDD +0.5 VDD +0.5 +10 +125 Unit V V V mA C Remark
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current, temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
s RECOMMENDED OPERATING CONDITIONS
Parameter Symbol Value Min. 1.0 Power supply voltage Input voltage Operating temperature VDD, VP VIN Ta 1.2 1.3 GND -20 Typ. - - - - - Max. 1.5 1.5 1.5 VDD +60 V C V Unit Remark For 220 MHz For 330 MHz For 450 MHz VDD = VP
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the semiconductor device. All of the device's electrical characteristics are warranted when the device is operated within these ranges. Always use semiconductor devices within their recommended operating condition ranges. Operation outside these ranges may adversely affect reliability and could result in device failure. No warranty is made with respect to uses, operating conditions, or combinations not represented on the data sheet. Users considering application outside the listed conditions are advised to contact their FUJITSU representatives beforehand.
6
MB15C02
s ELECTRICAL CHARACTERISTICS
(For 220 MHz :VDD = Vp = 1.0 to 1.5 V, Ta = -20 to +60C) (For 330 MHz :VDD = Vp = 1.2 to 1.5 V, Ta = -20 to +60C) (For 450 MHz :VDD = Vp = 1.3 to 1.5 V, Ta = -20 to +60C) Parameter Symbol Condition (VDD=1.0V/220MHz) (VDD=1.2V/330MHz) (VDD=1.3V/450MHz) (VDD=1.0V) (VDD=1.2V) (VDD=1.3V) Programmable divider (VDD=1.0 to 1.5V) (VDD=1.2 to 1.5V) (VDD=1.3 to 1.5V) Programmable reference divider AC coupling AC coupling - - VIN=VDD VIN=GND IOH = -0.2 mA IOL = 0.2 mA IOL = 0.2 mA VOUT = GND to VP VOUT = VDD Value Min. - - - - - - 10 10 10 5 -2.0 -2.0 VDD - 0.2 - - -1.0 VDD - 0.2 - - -100 - Typ.*3 0.6 1.0 1.3 50 70 80 - - - - - - - - - - - - - - - Max.*4 1.2 1.8 2.2 250 300 350 220 330 450 20 - - - 0.2 +1.0 - - 0.2 0.2 100 100 V nA nA A Unit
Power supply current
Active Mode
IDD *1
mA
Power saving current
Power saving mode
IDDS *2
A
fin Operating frequency OSCIN Input sensitivity fin OSCin Except for fin and OSCin Except for fin, OSCin and TEST Except for OSCOUT and P P High impedance Do cutoff current P H level L level H level L level H level L level L level
fin
MHz
fOSC Vfin VOSC VIH VIL IIH IIL VOH VOL VOL IOFF1 IOFF2
MHz dBm dBm V
Input voltage
Input current
Output voltage
V
*1: Conditions; Inputs except for fin, OSCIN and TEST are grounded, Outputs are opened. Specifying the current flowing in VDD and Vp at operating state under conditions of VDD = Vp, fin = 220 MHz, or 330 MHz, and OSCIN = 12.8 MHz. The current at locking state shows IDD Supply current (P .20). *2: Conditions; PS = Low, Inputs except for fin, OSCIN and TEST are grounded, Outputs are opened. *3: Condition; Ta = 25C *4: Condition; Ta = -20 to +60C
7
MB15C02
s FUNCTION DESCRIPTIONS 1. Pulse Swallow Function
The divide ratio can be calculated using the following equation: fVCO = [(M x N) + A] x fOSC / R (A < N) fVCO N A fOSC R M : : : : : : Output frequency of external voltage controlled oscillator (VCO) Preset divide ratio of binary 12-bit programmable counter (5 to 4,095) Preset divide ratio of binary 6-bit swallow counter (0 to 63) Output frequency of the reference frequency oscillator Preset divide ratio of binary 14-bit programmable reference counter (5 to 16,383) Preset modulus of dual modulus prescaler (64)
2. Circuit Description
(1) Intermittent operation
The intermittent operation of the MB15C02 refers to the process of activating and deactivating its internal circuit thus saving power dissipation otherwise consumed by the circuit. If the circuit is simply restarted from the power saving state, however, the phase relation between the reference frequency (fr) and the programmable frequency (fp), which are the input to the phase comparator, is not stable even when they are of the same value. This may cause the phase comparator to generate an excessively large error signal, resulting in an out-of-synth lock frequency To preclude the occurrence of this problem, the MB15C02 has an intermittent mode control circuit which forces the frequencies into phase with each other when the IC is reactivated, thus minimizing the error signal and resultant lock frequency fluctuations. The intermittent mode control circuit is controlled by the PS pin. Setting pin PS high provides the normal operation mode and setting the pin low provides the power saving mode. The MB15C02 behavior in the active and power saving modes is summarized below. Active mode (PS = "H") All MB15C02 circuits are active and provide the normal operation. Power saving mode (PS = "L") The MB15C02 stops any circuits that consume power heavily as well as cause little inconvenience when deactivated and enters the low-power dissipation state. Do, R, P and LD pins take the same state as when the PLL is locked. , Do pin becomes a high-impedance state and the input voltage to the voltage control oscillator (VCO) is maintained at the same level as in active mode(that is, locked state) according to a time constant of a low pass filter (LPF). Consequently , the output frequency from the VCO (fvco) is maintained at approximately the lock frequency. Applying the intermittent operation by alternating the active and power saving modes, and also forcing the phases of fr and fp to synchronize when it switches from stand by to active modes, the MB15C02 can keep the power dissipation of its entire circuitry to the minimum.
(2) Programmable divider
The fvco input through fin pin is divided by the programmable divider and then output to the phase comparator as fp. It consists of a dual modulus prescaler, a 6-bit binary swallow counter, a 12-bit binary programmable counter, and a controller which controls the divide ratio of the prescaler
8
MB15C02
Divide ratio range: Prescaler : M = 64, M+1=65 Swallow counter : A = 0 to 63 Programmable counter : N = 5 to 4095 The MB15C02 uses the pulse swallow method; consequently, the divide rations of the swallow and programmable counters must satisfy the relationship N>A. The total divide ratio of the programmable divider is calculated as follows: Total divide ratio = (M + 1) x A + M x (N - A) = M x N + A = 64 x N + A When N is set within 564 must be satisfied for the total divider to be set within 0(3) Programmable reference divider
The programmable reference divider divides the reference oscillation frequency(fosc) from the crystal oscillator connected between OSCin and OSCout pins or from the external oscillator input taken in directly through OSCin, pin and then, sends the resultant fr to the phase comparator. It consists of a 14-bit binary programmable reference counter. When the output from the external oscillator is to be input directly to OSCin, pin the connection must be AC coupled and OSCout pin is left open. Also, to prevent OSCout from malfunctioning, its traces on the printed circuit board must be kept minimal or eliminated entirely; whenever possible, it must be free of any form of load. The following divider is used: Programmable reference counter : R = 5 to 16383 The fr and fosc have the following relation: fr = fosc / R
(4) Phase comparator
The phase comparator detects the phase difference between the outputs fr and fp from the dividers and generates an error signal that is proportional to phase difference. The outputs from the phase comparator include 1) Do which takes on one of the three states, namely, "L" (low), "H" (high), and "Z" (high impedance), and is sent to the LPF, 2)R, 3)P 4)LD which indicates the PLL lock or unlock states. , (a) Phase comparator The phase comparator detects the phase error between fr and fp, then generates an error signal that is proportional to the phase error. The roles of the fr and fp supplied to the phase comparator may be reversed by switching the logical input level of pin FC. This inverts the logical level of the Do output. The logical level of Do output may be selected according to the characteristics of the external LPF and the VCO. (Refer to Table 1.)
Table. 1 Phase comparator inputs/output relationships
Output Phase relation fr > fp fr = fp fr < fp FC = "L" Do H Z L R L L H P L Z Z Do L Z H FC = "H" R H L L P Z Z L
9
MB15C02
(b) Charge pump
The charge pump is available in two forms: internal external. Internal charge pump output (Do) External charge pump outputs (R, P)
(c) Phase comparator input/output waveforms
The phase comparator outputs logic levels summarized in Table 1, according to the phase error between fr and fp. Note that P is an Nch open drain output. The pulse width of the phase comparator outputs are identical and equal to the phase error between fr and fp as shown in Figure 1.
fr
fp When FC = "L" High Z
Do
R
P
High Z
When FC = "H" Do High Z
R
P
High Z
High Z : High impedance state fp : Nch open output
Figure 1. Phase comparator input/output waveform
10
MB15C02
(d) Lock detector
The lock detector detects the lock and unlock states of the PLL. The lock detector outputs "H" when the PLL enters the lock state and outputs "L" when the PLL enters the unlock state as shown in Figure 2. When PS = "L", the lock detector outputs "H" compulsorily.
fr
fp
LD
Figure 2. Phase comparator input/output waveforms (Lock detector)
11
MB15C02
4. Setting the Divide Ratio
(1) Serial data format
The format of the serial data is shown is Figure 3. The serial data is composed of a control bit and divide ratio setting data. The control bit selects the programmable divider or programmable reference divider. In case of the programmable divider, serial data consists of 18 bits(6 bits for the swallow counter and 12 bits for the programmable counter) and 1 control bit as shown in Figure 3.1. In case of the programmable reference divider, the serial data consists of 14 divider bits and 1 control bit as shown in Figure 3.2. The control bit is set to 0 to identify the serial data for the programmable divider and to 1 to select the serial data for the programmable reference divider.
Figure 3. Serial data format
LSB Direction of data input MSB
C
A 0
A 1
A 2
A 3
A 4
A 5
N 0
N 1
N 2
N 3
N 4
N 5
N 6
N 7
N 8
N 9
10
N
11
N
Swallow counter control bit
Programmable counter
Figure 3.1. Divide ratio for the programmable divider
LSB Direction of data input MSB
C
R 0
R 1
R 2
R 3
R 4
R 5
R 6
R 7
R 8
R 9
10
R
11
R
12
R
13
R
Programmable reference counter control bit
Figure 3.2. Divide ratio for the programmable reference divider
12
MB15C02
(2) The flow of serial data
Serial data is received via data pin in synchronization with the clock input and loaded into shift register which contains the divide ratio setting data and into the control register which contains the control bit. The logical product (through the AND gate in Figure 4) of LE and the control register output (i.e., control bit) is fed to the enable input of the latches. Accordingly, when LE is set high, the latch for the divider identified by the control bit is enabled and the divide ratio data from the shift register is loaded into the selected counter (s).
Programmable reference divider
14-bit binary programmable reference counter
14 AND
14-bit latch
14
Data C* Clock LE AND 18
18-bit shift register
18-bit latch
6 Prescaler
12 Programmable divider
6-bit binary swallow counter 12-bit binary programmable counter
* : Control register
Figure 4. The flow of serial data (3) Setting the divide ratio for the programmable divider
Columns A0 to A5 of Table 2.1 represent the divide ratio of the swallow counter and columns N0 to N11 of Table2.2 represent the divide ratio of programmable counter.
Table. 2 Divide ratio for the programmable divider Table.2.1 Swallow counter divider A Table2.2 Programmable counter divider N
Divide ratio (A) 0 1 63 A 0 0 1 1 A 1 0 0 1 A 2 0 0 1 A 3 0 0 1 A 4 0 0 1 A 5 0 0 1 Divide ratio (N) 5 6 4095 N 0 1 0 1 N 1 0 1 1 N 2 1 1 1 N 3 0 0 1 N 4 0 0 1 N 5 0 0 1 N 6 0 0 1 N 7 0 0 1 N 8 0 0 1 N 9 0 0 1 NN 10 11 0 0 1 0 0 1
Note: Less than 5 is prohibited. 13
MB15C02
(4) Setting the divide ratio for the programmable reference divider
Columns R0-R13 of Table 3 represent the divide ratio of the programmable reference counter. The control bit is set to 1.
Table.3 Divide ratio for the programmable reference divider
Divide ratio (R) 5 6 16383 R 0 1 0 1 R 1 0 1 1 R 2 1 1 1 R 3 0 0 1 R 4 0 0 1 R 5 0 0 1 R 6 0 0 1 R 7 0 0 1 R 8 0 0 1 R 9 0 0 1 R 10 0 0 1 R 11 0 0 1 R 12 0 0 1 R 13 0 0 1
(5) Setting data input timing
The MB15C02 uses 19 bits of serial data for the programmable divider and 15 bits for the programmable reference divider. When more bits of serial data than defined for the target divider are received, only the last valid serial data bits are effective. To set the divide ratio for the MB15C02 dividers, it is necessary to supply the Data, Clock, and LE signals at the timing shown in Figure 5. t1 (>1 s): Data setup time t2 (>1 s): Data hold time t3 (> s): Clock pulse width t5 (>1 s): LE pulse width t4 (>1 s): LE setup time to the rising edge of last clock
Data
Clock
LE t2 t1 t3 t4 t5
Figure 5. Serial data input timing
14
MB15C02
Since the divide rations are unpredictable when the MB15C02 is turned on, it is necessary to initialize the divide ratio for both dividers at power-on time. As shown in Figure 6, after setting the divide ratio for one of the dividers (e.g., programmable reference divider), set LE to "H" level before setting the divide ratio for the other dividers (e.g., programmable divider). To change the divide ratio of one of the divider after initialization, input the serial data only for that divider (the divide ratio for the other divider is preserved).
Data
Serial data for programmable reference divider 15 clocks
1*
Serial data for programmable divider 19 clocks
0*
Clock
LE * : Control bit
Figure 6. Inputting serial data(Setting divisors)
15
MB15C02
s TYPICAL CHARACTERISTICS
1. fin Input Sensitivity
fin input frequency vs. Input sensitivity 20.0 Ta = +25C 10.0
0.0 Input sensitivity (dBm) -10.0 -20.0 -30.0 -40.0 -50.0 -60.0 V DD = 1.0 V V DD = 1.2 V V DD = 1.3 V V DD = 1.5 V 0 100 200 300 400 500 600 700 800 900 1000
fin input frequency (MHz)
2. OSCIN Input Sensitivity
OSC IN input frequency vs. Input sensitivity 20.0 Ta = +25C 10.0
0.0 Input sensitivity (dBm) -10.0 -20.0 -30.0 -40.0 -50.0 -60.0 V DD = 1.0 V V DD = 1.2 V V DD = 1.3 V V DD = 1.5 V 0 50 100 150 200 250 300 350 400 450 500
OSC IN input frequency (MHz)
16
MB15C02
3. fin Power Supply Voltage
(MHz) 1000 900 800 Input frequency (MHz) 700 600 500 400 300 200 100 0 0.9 Power supply voltage vs. fin input frequency Vfin = -2.0 (dBm) Ta = +25C
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
Power supply voltage (V)
4. OSCIN Power Supply Voltage
Power supply voltage vs. OSC IN input frequency 500 450 400 350 Input frequency (MHz) 300 250 200 150 100 50 0 0.9 Vfin = -2.0 (dBm) Ta = +25C
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
Power supply voltage (V)
17
MB15C02
5. IDD Power Supply Current
Input frequency vs. power supply current 5.0 Ta = +25C 4.5 4.0 3.5 I DD (mA) 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0 100 200 300 400 500 600 700 800 900 1000 Input frequency (MHz) V DD = 1.0 V V DD = 1.2 V V DD = 1.3 V V DD = 1.5 V
18
MB15C02
6. Do (Charge Pump) Power Supply Voltage
V DD (V p) vs. I OL (at V OL = 0.2 V) 5.0 Ta = +25C 4.5 4.0 3.5 I OL (mA) 3.0 2.5 2.0 1.5 1.0 0.5 0.0 0.8
0.9
1.0
1.1
1.2
1.3 V DD (V)
1.4
1.5
1.6
1.7
1.8
V DD (V p) vs. I OH (at V OH = V DD - 0.2 V) -5.0 Ta = +25C -4.5 -4.0 -3.5 -3.0 I OH (mA) -2.5 -2.0 -1.5 -1.0 -0.5 0.0 0.8
0.9
1.0
1.1
1.2
1.3 V DD (V)
1.4
1.5
1.6
1.7
1.8
19
MB15C02
7. Spectrum Wave Form
ATTEN 10 dB RL 0 dBm UAUG 16 10dB/ MKR -85.50 dB 25.0 kHz * LOCK Frequency : 286.0 MHz (fr = 25 kHz) * V DD = 1.2 V, V p = 1.2 V Ta = +25C
MKR D 25.0 kHz S -85.50 dB
CENTER 286.0000 MHz *RBW 1.0 kHz VBW 1.0 kHz
SPAN 200.0 kHz *SWP 1.00 s
ATTEN 10 dB RL 0 dBm
UAUG 50 10dB/
MKR -53.84 dB 800 Hz * LOCK Frequency : 286.0 MHz ( fr = 25 kHz) * VDD = 1.2 V, V p = 1.2 V Ta = +25C
MKR D 800 Hz S -53.84 dB
CENTER 286.00000 MHz *RBW 100 Hz VBW 100 kHz
SPAN 20.00 kHz *SWP 3.00 s
* Test circuit
DO 15 k 4.3 k 6800 pF 4700 pF 68000 pF
VT (to VCO)
* VCO : K V = 6 MHz/v
20
MB15C02
8. Lock Up Time
* LOCK Frequency: 290.0 MHz to 286.0 MHz (fr = 25 kHz) * VDD = 1.2 V, VP = 1.2 V, Ta = +25C 290.0 MHz 286.0 MHz, within 1 kHz
4.00 ms
MKr x : 3.99999984 ms y : -4.00100 MHz 286.0050 MHz A euts N/A
2.00 kHz/div
285.9950 MHz 0s 10.0000000 ms
* LOCK Frequency: 286.0 MHz to 290.0 MHz (fr = 25 kHz) * VDD = 1.2 V, VP = 1.2 V, Ta = +25C 286.0 MHz 290.0 MHz, within 1 kHz
6.20 ms
MKr x : 6.19999943 ms y : 4.00082 MHz 290.0050 MHz A euts N/A
2.00 kHz/div
289.9950 MHz 0s 10.0000000 ms
(Continued)
21
MB15C02
(Continued)
* LOCK Frequency: PS on to 286.0 MHz (fr = 25 kHz) * VDD = 1.2 V, VP = 1.2 V, Ta = +25C PS ON 286.0 MHz, within 1 kHz
2.00 ms
MKr x : 1.99999978 ms y : -680 Hz 286.0050 MHz A euts N/A
2.00 kHz/div
285.9950 MHz 0s 8.0000000 ms
PS
1V 0V
s USAGE PRECAUTIONS
* This device should be transported and stored in anti-static containers. * This is a static-sensitive device; take proper anti-ESD precautions. Ensure that personnel and equipment are properly grounded. Cover workbenches with grounded conductive mats. * Always turn the power supply off before inserting or removing the device from its socket. * Protect leads with a conductive sheet when handling or transporting PC boards with devices.
s ORDERING INFORMATION
Parts number MB15C02PFV1 MB15C02PFV2 Package 16-pin Plastic SSOP (FPT-16P-M05) 20-pin Plastic SSOP (FPT-20P-M03) Remarks
22
MB15C02
s PACKAGE DIMENSIONS
16 pins, Plastic SSOP (FPT-16P-M05)
* 5.000.10(.197.004)
*: These dimensions do not include resin protrusion.
1.25 -0.10 +.008 .049 -.004
+0.20
(Mounting height)
0.10(.004)
INDEX
*4.400.10
(.173.004)
6.400.20 (.252.008)
5.40(.213) NOM
0.650.12 (.0256.0047)
0.22 -0.05 +.004 .009 -.002
+0.10
"A"
0.15 -0.02 +.002 .006 -.001
+0.05
Details of "A" part 0.100.10(.004.004) (STAND OFF)
4.55(.179)REF
0
10
0.500.20 (.020.008)
C
1994 FUJITSU LIMITED F16013S-2C-4
Dimensions in mm (inches)
(Continued)
23
MB15C02
(Continued)
20 pins, Plastic SSOP (FPT-20P-M03)
* 6.500.10(.256.004)
*: These dimensions do not include resin protrusion.
1.25 -0.10 +.008 .049 -.004
+0.20
(Mounting height)
0.10(.004)
INDEX
*4.400.10 6.400.20
(.173.004) (.252.008)
5.40(.213) NOM
0.650.12 (.0256.0047)
0.22 -0.05 +.004 .009 -.002
+0.10
"A"
0.15 -0.02 +.002 .006 -.001
+0.05
Details of "A" part 0.100.10(.004.004) (STAND OFF)
5.85(.230)REF
0
10
0.500.20 (.020.008)
C
1994 FUJITSU LIMITED F20012S-2C-4
Dimensions in mm (inches)
24
MB15C02
FUJITSU LIMITED
For further information please contact:
Japan FUJITSU LIMITED Corporate Global Business Support Division Electronic Devices KAWASAKI PLANT, 4-1-1, Kamikodanaka Nakahara-ku, Kawasaki-shi Kanagawa 211-8588, Japan Tel: 81(44) 754-3763 Fax: 81(44) 754-3329
All Rights Reserved. The contents of this document are subject to change without notice. Customers are advised to consult with FUJITSU sales representatives before ordering. The information and circuit diagrams in this document are presented as examples of semiconductor device applications, and are not intended to be incorporated in devices for actual use. Also, FUJITSU is unable to assume responsibility for infringement of any patent rights or other rights of third parties arising from the use of this information or circuit diagrams. FUJITSU semiconductor devices are intended for use in standard applications (computers, office automation and other office equipment, industrial, communications, and measurement equipment, personal or household devices, etc.). CAUTION: Customers considering the use of our products in special applications where failure or abnormal operation may directly affect human lives or cause physical injury or property damage, or where extremely high levels of reliability are demanded (such as aerospace systems, atomic energy controls, sea floor repeaters, vehicle operating controls, medical devices for life support, etc.) are requested to consult with FUJITSU sales representatives before such use. The company will not be responsible for damages arising from such use without prior approval. Any semiconductor devices have an inherent chance of failure. You must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. If any products described in this document represent goods or technologies subject to certain restrictions on export under the Foreign Exchange and Foreign Trade Law of Japan, the prior authorization by Japanese government will be required for export of those products from Japan.
http://www.fujitsu.co.jp/
North and South America FUJITSU MICROELECTRONICS, INC. Semiconductor Division 3545 North First Street San Jose, CA 95134-1804, USA Tel: (408) 922-9000 Fax: (408) 922-9179 Customer Response Center Mon. - Fri.: 7 am - 5 pm (PST) Tel: (800) 866-8608 Fax: (408) 922-9179
http://www.fujitsumicro.com/
Europe FUJITSU MIKROELEKTRONIK GmbH Am Siebenstein 6-10 D-63303 Dreieich-Buchschlag Germany Tel: (06103) 690-0 Fax: (06103) 690-122
http://www.fujitsu-ede.com/
Asia Pacific FUJITSU MICROELECTRONICS ASIA PTE LTD #05-08, 151 Lorong Chuan New Tech Park Singapore 556741 Tel: (65) 281-0770 Fax: (65) 281-0220
http://www.fmap.com.sg/
F9902 (c) FUJITSU LIMITED Printed in Japan
25

▲Up To Search▲

Price & Availability of MB15C02PFV2

	To Download MB15C02PFV2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .